Triplett CamView PTZ – PN: 8000 Manual do Utilizador Página 1

84-887 REV A 8/12CamView PTZTMInstruction Manual

Page 82.3 Controls and Indicators

AC Power Indicator. Lights when CamView is operating from AC power.1Receive Indicator: Lights when PTZ signals are being Received.2Transmit Indicator:

UP Button : Tilt the controlled camera ‘up’. Navigate upward on a menu. Change a parameter value. 11LEFT Button : Pan the controlled camera ‘left’. Na

Press to Reset CamView to factory defaults.22External power jack (5V, 2A): Use only the provided power adapter.23UTP Cable Test jack (RJ-45): Use to t

Page 12 The CamView is shipped with the battery disconnected to prevent any battery drain that may reduce the battery life. Prior to the use of the

To turn the unit on, press for about 2 seconds and release when the unit powers up. After depleting the battery, connect the supplied ba

3.1 General InstructionsTo turn the unit on, press for about 2 seconds and release when the unit powers up.To turn the unit o, press

Use the following diagram as a guide to connect the CamView to a PTZ camera.Page 153 Using the CamView Cont. Connect the video output of the camer

Pressing the button reveals the main menu. By repeatedly pressing the button, the user can select any of the CamView’s test functions

Page 173.2 Introduction to Menu & Functions Cont.3. Color bar generatorThe CamView contains a built-in Color bar generator. Seven standard PA

Page 183.3 Video Monitor Mode/ PTZ Controller Parameter Setting3.3 Video Monitor Mode (PTZ controller)Press to select ‘PTZ controller’.

Page 193.3 Video Monitor Mode/ PTZ Controller Parameter Setting Cont.3.3.1 Setting PTZ Parameters (Overview)In the PTZ controller mode,

Page 203.3 Video Monitor Mode/ PTZ Controller Parameter Setting Cont.E. Pan speedMove the cursor to “Pan speed”. Select a value for the Pan speed

Page 213.3.2 Setting PTZ Parameters (Details)Camera Information Detailed information about a PTZ camera must be known in order to set it up or tes

A. Connecting the CamView to an RS-485 PTZ Camera:Connect the video signal from the PTZ camera to the VIDEO IN jack of the CamView. This is usually

Page 233.3.2 Setting PTZ Parameters (Details) Cont.F. Testing PTZ communication If the PTZ setup is correct, and the camera is operating properly,

Page 243.3.2 Setting PTZ Parameters (Details) Cont.3.3.3 Using PresetsPresets’ are ‘pointing locations’ stored in the camera. The camera may be po

Page 253.3.4 Accessing a PTZ Camera Menu PTZ cameras have many functions that can be accessed from their main menu. When the menu is accessed, the

Page 26Camera Menu (For reference only)MAIN MENU1. DISPLAY SETUP2. CAMERA SETUP3. CONTROL SETUP4. CAMERA MASK SET5. PROGRAM6. PAL CAMERA7. CAM DEFAULT

Page 27Other presets available in the example cameraPreset 033 ……….. Auto-rotate 180 degrees (ip)Preset 034 ……….. Reset Pan / Tilt to the origin (zer

• Thank you for purchasing the Triplett CamView PTZ CCTV Monitor with PTZ Controller. Please read the complete manual carefully before using

Page 28‘Brightness’ can be varied from -128 to +127. A typical setting is +0.‘Contrast’ can be varied from -128 to +127. A typical setting is +40.‘Sat

Page 293.5. Color Bar Generator The ‘Color bar generator’ can generate a color bar signal in 7 dierent video formats. Select the forma

Page 303.6 Cable Testing The CamView can test cables consisting of 2 to 8 wires. The ends of the cable must be terminated in RJ-45 pl

3.7. Capturing PTZ protocol The CamView can view PTZ codes using its ‘Data monitor’ mode. This allows the user to verify that the P

3.8. Device setting (User Settings) Use the button to select ‘Device setting’. To change any of the settings, use or

Page 33This feature is intended to preserve the charge on the battery if the prod-uct is unused for some period of time. The ‘Auto power o’ feature c

re-initialized. To initialize the Address Search feature, select the Device set-ting menu, and use the arrow keys to select Address search and change

Page 354. SpecificationsVideo Monitor Formats Supported NTSC and PAL (Auto Selected) Display 2.6 inch TFT-LCD ,960 x 240 resolution Displ

Page 364. Specifications Cont.RJ-45 CABLE TEST Tests Performed Tests 2 to 8 conductors for Opens, Shorts,

Environmental Working Temperature -30F to 160F Working Humidity 0%-90% RHPhysical Dimensions 2” x 4” x 6” Weight 10oz (CamView on

Safety Information ...1Introduction ...

Page 38Triplett One Year Limited WarrantyTriplett warrants instruments and test equipment manufactured by it to be free from defective material or wor

Page 39Triplett One Year Limited Warranty Cont.The purchaser agrees to assume all liability for any damages and bodily injury which may result from th

Notes

Notes

Page 3 • Use this product in accordance with any prevailing safety rules that may be imposed by local or federal authorized bodies. • Do not

Page 4 The Triplett CamView PTZ is a multi-function test tool designed to aid CCTV and Security electronics installers and maintenance technicians.

Page 5 • Full Color 2.6” TFT-LCD Video Monitor • OSD (On Screen Display) of all Modes, Functions, and Settings • Adjustable LCD Brightness / Con

Page 6The following items are included with your Triplett CamView PTZ.2.2 Included ItemsRemote Terminator for LAN Cable TestingBNC to BNC Patch Cable

Page 72.2 Included Items Cont.Carrying CaseShoulder Strap for Carrying CaseNeck Strap for CamView Instruction Manual